Priority HVAC Services in Grand Rapids, MI

Completed air conditioner installation with integration to existing two-stage furnace, including proper two-wire thermostat wiring for staging control. Installed flush kit for refrigerant line cleaning, ran 10 feet of 3/4" PVC condensate drain line, and installed whip assembly with appropriate fusing for electrical connection. System tested and operational with all components functioning as designed.

Completed full HVAC system replacement including removal of legacy lowboy furnace and air conditioning unit. Installed new furnace with repositioned orientation toward chimney for proper venting, installed 25-foot chimney liner, and connected new AC system with 20-foot refrigeration line set. Modified water heater gas piping with correct nipple to ensure plumb installation and proper gas line configuration.

Completed compressor replacement on Lennox unit per PO 169870605-001. Removed failed compressor, installed new hermetic compressor unit with proper copper line connections, and ensured all mounting hardware was secured to base plate. Failed compressor was tagged and prepared for warranty return processing as required.

Completed installation of new air conditioning system. Installed refrigerant line set with insulated copper tubing and electrical disconnect box with 3-pole, 50-amp capacity. System properly connected, tested, and verified operational.

Completed installation of 50-gallon tall natural gas water heater with required safety upgrades. Installed new drain pan beneath unit and ran 4-inch chimney liner from water heater through rooftop, accessing roof from rear of structure. Connected new flexible gas supply line with shutoff valve to unit and verified all connections for proper operation and code compliance.

Completed air conditioner installation with new cased evaporator coil upgrade from existing 16 5/8" unit to 17 1/2" wide cased coil to improve compatibility with furnace cabinet and S-transition configuration. Installed 25-foot refrigerant lineset with copper tubing and insulation, ran 10 feet of 3/4" PVC condensate drain line, and replaced electrical fuse component to meet system specifications.

Inspected furnace heat exchanger and confirmed presence of holes causing previous CRI failure. Removed and replaced defective heat exchanger assembly with new unit. Performed post-installation inspection and verified system passed CRI requirements for municipal compliance documentation.

Completed full HVAC system replacement in single-wide mobile home, removing existing packaged A/C unit and short furnace cabinet, then installing tall furnace cabinet with mobile home coil and new condensing unit. Installed 35-foot refrigerant lineset with drilling and penetration through furnace cabinet, removed and capped existing 14-inch diameter supply trunk at main plenum connection, and installed appropriate roof jack for domed mobile home roof profile. Replaced thermostat with new stat wire, completed refrigerant charging, and verified all system operations per manufacturer specifications.

Installed new 21-inch cased evaporator coil to match existing furnace width, replaced condensate pump, and ran 20-25 feet of refrigerant lineset between indoor and outdoor units. Added GFCI electrical outlet for code compliance and installed double return air grille in furnace room wall to improve airflow distribution. System startup completed successfully with all components operating within manufacturer specifications.

Completed full system replacement of existing 90% efficiency furnace and air conditioning unit. Removed existing 24.5" wide uncased coil system with double R drops and 1" filter racks. Installed new 21" wide furnace system, requiring refabrication of 1" filter racks on both sides for proper fitment. Reused existing 2-pipe 3" diameter venting system that was buried in drywall ceiling. Installed flush kit with 15 feet of 3" PVC, 10 feet of 2" PVC, and 20 feet of 3/4" PVC for proper condensate drainage. Added new floor pan for equipment protection. Fabricated and installed new 90-degree boots and drops for optimized ductwork configuration. System tested and verified for proper operation upon completion.

Completed full HVAC system installation including elite furnace and air conditioning unit with 35-foot refrigeration line set and condensate drain pan. Replaced existing single pipe termination with 60 feet of 2-inch PVC venting, installed 6 feet of 4-inch single wall venting for water heater with 3 elbows, and upgraded humidifier connection from saddle valve to Sioux Chief valve for improved water supply reliability.

Completed air conditioning system replacement on existing 14 1/4" wide furnace with 180-degree uncased coil. Installed new 30-foot refrigerant line set connecting outdoor condensing unit to indoor coil, reused existing thermostat and condensate pump with GFI protection already in place.

Completed air conditioner installation on three-story commercial building with rooftop unit placement requiring crane service with 60-70 ft reach from rear parking lot. Installed 50 ft refrigerant lineset with insulated tubing, chasing new lines through existing structure from ground level through roof penetration, and replaced 250VAC fuse during system commissioning. Unit successfully installed and operational with all refrigerant lines properly secured and insulated throughout vertical chase.

Completed air conditioning system installation with 20-foot refrigerant line set and associated electrical components. Modified ductwork by upgrading two supply lines from 6-inch to 8-inch diameter to match existing 8-inch boots for improved airflow distribution. System commissioned and tested for proper operation after addressing previous homeowner-attempted repairs to the outdoor unit.

Responded to concern regarding noise originating from HVAC system. Upon arrival, tech lead conducted diagnostic assessment to verify noise source and confirm whether issue was related to air conditioning unit or furnace before proceeding with component replacement. Replaced defective blower motor and control board per work order specifications. Removed failed blower motor assembly with attached wiring harness and installed new components to restore proper system operation.

Replaced 40-gallon natural gas power vent water heater with new unit. Installed all necessary pipe fittings and connections, configured gas control valve assembly, and verified proper power vent operation. Unit tested and left in full working condition.

Responded to VIP Red Carpet Maintenance call for AC unit evaluation. Upon arrival, conducted comprehensive inspection of residential HVAC system located in basement utility area. Documented existing mechanical infrastructure including water heater, ductwork, insulated refrigerant lines, condensate pump assembly, and associated plumbing connections. Verified proper installation of foam-insulated copper piping, metallic ductwork routing, and condensate management system. Captured photographic documentation of all mechanical components, water heater specifications and safety labels, and overall system configuration for maintenance records. All equipment observed in operational condition with no immediate service concerns identified during visual inspection.

Arrived on site to replace outdoor unit under warranty but discovered a 6/4 transformer failure in the neighborhood had caused a power outage. Unable to complete the installation without power to the area. Documented current system conditions using refrigerant manifold and micron gauge, capturing pressure and temperature readings for reference upon return. Job rescheduled pending power restoration by utility company.

Completed full HVAC system replacement, upgrading from existing 80% efficiency furnace to new high-efficiency system with AC unit. Installed 30 ft refrigeration line set with insulated tubing and copper lines, routed to outdoor condenser location. Fabricated and installed custom ductwork including floor pan, return air drop, and 1" rack to accommodate 14.25" wide unit configuration. Installed 40 ft of 2" PVC condensate drain line and 10 ft of 3/4" PVC drainage. Configured venting system routing toward condenser side of residence. Mounted new programmable thermostat and wired to system controls. Installed fan-powered humidifier integrated with new furnace for whole-home humidity control. Replaced 40-gallon water heater, connecting existing 4" vent to 5" B-vent chimney system. Tested all components for proper operation, verified refrigerant charge, confirmed airflow balance, and ensured all safety controls functioning correctly.

Completed air conditioning system installation with new outdoor condenser unit leveled and positioned in crawlspace area. Installed new 50-foot refrigerant lineset connecting to existing 17.5-inch wide furnace equipped with raised 90-degree evaporator coil. Reused existing condensate pump and GFI outlet, ensuring proper electrical connections and drainage functionality for complete system operation.