Priority HVAC Services in Grand Rapids, MI

Completed installation of single-head mini-split ductless system with 20-foot line set following HOA approval of outdoor unit placement. Mounted condensing unit on concrete pad with proper electrical disconnect, installed wall-mounted indoor air handler, and ran refrigerant lines and electrical connections between units. System tested and operational upon completion.

Replaced existing 80% efficiency gas furnace (14 1/4" width) with new unit, reusing existing refrigerant drop and 16x25 1" filter rack. Installed new thermostat to replace existing unit. Utilized existing 4" B-vent connection and confirmed proper venting through existing chimney liner already in place. All connections tested and system commissioned successfully.

Completed installation of a 50-gallon natural gas power vent water heater. Unit was set in place, all water connections and gas lines were properly installed and tested, power vent system with PVC exhaust piping was configured and secured, and all safety controls including pressure relief valve were verified operational.

Removed existing boiler system and associated piping, then completed full installation of elite-efficiency forced air heating and cooling system. Installed new furnace with AC unit, bypass humidifier, programmable thermostat, condensate pump, chimney liner, and 1" 90-degree boot for return air drop. Performed extensive ductwork modifications including new supply plenum, return air drop, and integration of three existing basement supply runs that were previously installed for window AC unit. Coordinated with licensed electrician to install dedicated electrical circuits for both furnace and air conditioning unit. Installed refrigerant line sets with proper insulation and completed all ductwork design requirements for optimal air distribution throughout the home.

Completed installation of Legacy AC1 air conditioning system with 30-foot line set routed from the side of porch without steps, running close to cement patio and around to the back where outdoor unit was positioned. Added 6-inch round supply duct off plenum to living room corner location per customer request. Customer providing their own electrical connection for system completion.

Completed full HVAC system installation including legacy furnace and air conditioning unit replacement. Performed necessary duct modifications to accommodate new equipment and installed refrigerant line set with proper insulation. System components including accumulator/receiver were installed and connected, with follow-up electrical work scheduled pending site plan approval.

Completed full air conditioning system installation with new condensing unit paired to existing Bryant furnace. Installed 35-foot refrigerant line set routed through crawl space using insulated copper tubing, connected electrical components including 250VAC fuse protection, and ran 20-foot 3/4" PVC condensate drain line to ensure proper system drainage and operation.

Completed full HVAC system replacement including Evolution high-efficiency furnace and air conditioning system with DC 25 SEER condenser. Removed existing 17.5" wide 90% furnace and replaced with new unit, installed new evaporator coil with floor drain pan, and ran approximately 15-20 feet of refrigerant line set to outdoor condensing unit. Replaced all venting with 30 feet of 2" PVC and 10 feet of 3/4" PVC for condensate drainage. Reused existing return air drop and 16x25x1 filter rack. Installed new programmable thermostat and added single supply register to adjacent room with high return air configuration. Performed complete duct cleaning as part of installation to ensure optimal system performance and air quality.

Returned to site to replace failed contactor on HVAC unit as previously identified. Installed new contactor, verified proper electrical connections, and restored system operation. Performed NESU (National Equipment Safety Upgrade) inspection, documented refrigerant charge using calibrated scale, and confirmed all safety controls functioning within manufacturer specifications.

Completed inspection corrections for 90% direct vent furnace and split AC system installation. Installed proper support clamps for PVC vent piping at required four-foot intervals per code, replacing non-compliant electrical conduit supports. Sealed exterior wall penetrations around vent pipe terminations with approved sealant to eliminate gaps. Replaced cable ties on condensate pump discharge tubing with UL-listed clamps properly secured to overhead ceiling joists at minimum 32-inch spacing per mechanical code requirements.

Responded to diagnostic service call for air conditioning system following a power outage to assess potential electrical damage. Performed comprehensive system evaluation including thermostat functionality testing, electrical component inspection, and refrigerant circuit analysis. Documented existing plumbing infrastructure in utility area showing significant corrosion on copper piping connections and evidence of moisture exposure. Presented thermostat replacement options to homeowner and provided detailed repair recommendations based on diagnostic findings.

Completed full air conditioning system replacement, removing existing unit and installing new AC system with 35-foot copper line set and insulated suction line. Installed new 250VAC electrical fuse as part of electrical disconnect assembly to ensure proper overcurrent protection for the new equipment. System commissioned and tested successfully with all components operating within manufacturer specifications.

Completed warranty correction work to address failed mechanical inspection related to improper CSST bonding. Corrected the bonding of corrugated stainless steel tubing gas line to meet approved code requirements and industry standards. Re-inspected installation to ensure compliance with local mechanical code for rental property approval.

Completed installation of 4-head mini-split system with ground-mounted condenser positioned at minimum allowable height for cooling-only operation. Ran 150 feet of line set up exterior wall and through attic space to distribute refrigerant lines to all four indoor head units, with one head located on same side as outdoor unit. Verified electrical connections at service panel and ensured all circuit breakers were properly sized and functioning for system operation.

Completed full HVAC system installation including 80% efficiency furnace with corresponding air conditioning unit. Installed HumiFil humidifier cabinet with dedicated thermostat control, reused existing refrigerant line set after performing RX11 flush procedure to ensure system cleanliness. Replaced domestic water heater and installed new capacitor components to support system operation.

Completed installation of downflow cased air conditioning system with 18" evaporator coil. Installed 10-15 ft refrigerant lineset with copper tubing and insulation, ran 10 ft of 3/4" PVC condensate drain line, and replaced thermostat to complete system integration.

Replaced defective heat exchanger assembly on HVAC unit per purchase order specifications. Removed failed heat exchanger and installed new replacement unit featuring multi-tube construction with finned sections for optimal thermal transfer. Documented new component with photographs showing clean installation and verified proper fit within existing system framework.

Replaced faulty mixing valve on hydronic heating system and bled boiler to remove air from primary and secondary circuits. Verified proper operation of circulator pumps, checked expansion tank, and purged air from system using purge valves on return side of primary circuit to restore full heating functionality.

Completed full HVAC system replacement including installation of Signature series furnace and Merit air conditioning unit. Removed existing 48" furnace with no AC and installed new equipment with 2-pipe 2" diameter venting system, floor pan, and replaced return drop with 1" rack. Added AC condenser in backyard south of white pine tree with 35-foot lineset installation using insulated refrigerant lines and copper tubing. Installed bypass humidifier on new return drop, replaced condensate pump with new drain hose eliminating previous pinch points, and added 1" 90-degree boot. Coordinated with electrician for new breaker panel installation downstairs and AC disconnect with GFI outlet. Utilized 40 feet of 2" PVC and 10 feet of 3/4" PVC for drainage routing. System tested and operational upon completion.

Replaced defective backflow preventer and pressure reducing valve on hydronic heating system. Removed existing brass valve assembly and installed new pressure reducing valve with integral backflow prevention. System tested and verified proper operation with no leaks detected at connections.